Turbomeca s.a. turboshaft airworthiness directives
34 ADs in the reference matching Turbomeca s.a. turboshaft — from the Federal Register, checked every weekday. Applicability may depend on serial and effectivity: verify against the official AD before any maintenance action.
Reference last synced: 10/27/2026 17:00 UTC · 10,471 ADs indexed
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for certain Turbomeca S.A. Arriel 1, 1A, 1A1, 1A2, 1B, 1B2, 1C, 1C1, 1C2, 1D, 1D1, 1E, 1E2, 1K1, 1S, and 1S1 turboshaft engines. This AD requires removing the centrifugal impeller and replacing with a part eligible for installation. This AD was prompted by an anomaly that occurred during the grinding operation required by modification TU376, which increases the clea…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are superseding airworthiness directive (AD) 2010-11-10 for all Turbomeca S.A. Astazou XIV B and XIV H turboshaft engines. AD 2010- 11-10 requires inspection of certain third stage turbine wheels and removal of any damaged wheel. This AD requires expanding the population and frequency of repetitive inspections. This AD was prompted by a report of a third stage turbine wheel crack detected during engine overhaul.…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for all Turbomeca S.A. MAKILA 2A and MAKILA 2A1 turboshaft engines. This AD requires repetitive diffuser inspections and replacement of those diffusers that fail inspection. This AD was prompted by two occurrences of crack initiation on a ferrule of the diffuser. We are issuing this AD to prevent rupture of the ferrule of the diffuser, which could result in engine f…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for Turbomeca S.A. Arriel 1D and 1D1 turboshaft engines with a pre- modification (mod) TU357 gas generator module (M03), installed. This AD requires removing the pre-modification (mod) TU357 gas generator module (M03) and replacing with a part eligible for installation. This AD was prompted by reports of divergent rubbing between the piston shaft small diameter laby…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for certain Turbomeca S.A. Astazou XIV B and H turboshaft engines. This AD requires a one-time inspection of the front surface of the 3rd stage turbine for a groove. This AD was prompted by a report of a crack on the 3rd stage turbine wheel. We are issuing this AD to prevent cracks in the 3rd stage turbine wheel, failure of the engine, in-flight shutdown, and loss o…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for all Turbomeca S.A. Arriel 2E turboshaft engines. This AD requires removing the pre-TU 193 adjusted high-pressure/low-pressure pump and metering valve assembly and replacing it with a part that is eligible for installation. This AD also requires replacing the constant delta- pressure (delta-P) diaphragm of the fuel metering valve. This AD was prompted by reports…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are superseding airworthiness directive (AD) 2006-23-17 for certain Turbomeca S.A. Turmo IV A and IV C turboshaft engines. AD 2006- 23-17 required repetitive inspections of the centrifugal compressor intake wheel (inducer) blades for cracks and corrosion, replacement of parts that fail inspection, and replacement of the TU 197 standard centrifugal compressor. This AD requires the same inspections, but at revised…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for certain Turbomeca S.A. Arriel 2B, 2B1, 2C, 2C1, 2C2, 2D, 2E, 2S1, and 2S2 turboshaft engines. This AD requires inspection, and, depending on the results, removal of the engine accessory gearbox (AGB). This AD was prompted by a report of an uncommanded in-flight shutdown (IFSD) of an Arriel 2 engine caused by rupture of the 41-tooth gear, which forms part of the…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for certain Turbomeca S.A. Makila 2A and 2A1 turboshaft engines. This AD requires tightening the nut attaching the swivel union to the engine power turbine module M04. This AD was prompted by two occurrences of commanded in-flight shutdown following low oil pressure warning. We are issuing this AD to prevent loosening of the nut and oil leakage from the low-pressure…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for certain Turbomeca S.A. Arriel 1E2 turboshaft engines. This AD requires removing the tachometer box on affected engines. This AD was prompted by reports of uncommanded in-flight shutdowns (IFSDs). We are issuing this AD to prevent failure of the tachometer box, which could lead to failure of the engine, IFSD, and loss of control of the helicopter.
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for all Turbomeca S.A. ARRIEL 2C, 2C1, 2C2, 2S1, and 2S2 turboshaft engines with modification TU34 or TU34A installed. This AD requires inspecting the torque conformation box (TCB) for correct resistance values and removing TCBs that fail inspection before further flight. This AD was prompted by TCB failures. We are issuing this AD to prevent failure of the TCB, los…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for certain Turbomeca S.A. Arrius 2F turboshaft engines with a certain part number oil pump installed. This AD requires inspection, and if necessary, replacement before further flight of the oil pump driver assembly and/ or the oil pump shaft, or the oil pump itself. This AD was prompted by cases of deterioration of the gas generator front bearing due to a link loss…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are superseding airworthiness directive (AD) 2014-19-05 for all Turbomeca S.A. Arriel 1A1, 1A2, 1B, 1C, 1C1, 1C2, 1D, 1D1, 1E2, 1K1, 1S, 1S1, 2B, 2B1, 2C, 2C1, 2C2, 2S1, and 2S2 turboshaft engines. AD 2014-19-05 required an initial one-time vibration check of the engine accessory gearbox (AGB) on certain Arriel 1 and Arriel 2 model engines, and repetitive vibration checks for all Arriel 1 and Arriel 2 engines. Th…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are superseding airworthiness directive (AD) 2014-01-01 for all Turbomeca S.A. Arrius 2F turboshaft engines. AD 2014-01-01 required a one-time inspection of the ejector assembly nozzle of certain serial number (S/N) lubricating devices and, if a discrepancy was found, removal and replacement of the affected ejector assembly nozzle with a part eligible for installation. This AD requires the same action as AD 2014-…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for all Turbomeca S.A. Arriel 1A1, 1A2, 1B, 1C, 1C1, 1C2, 1D, 1D1, 1E2, 1K1, 1S, 1S1, 2B, 2B1, 2C, 2C1, 2C2, 2S1, and 2S2 turboshaft engines. This AD requires an initial one-time vibration check of the engine accessory gearbox (AGB) on certain higher risk Arriel 1 and Arriel 2 model engines. This AD also requires repetitive vibration checks of the engine AGB for all…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for certain Turbomeca S.A. Makila 2A and Makila 2A1 turboshaft engines. This AD requires initial and repetitive visual inspections, and replacement of the splines of the high-pressure (HP) fuel pump/metering valve and the module M01 drive gear, if necessary. This AD was prompted by the failure of two HP fuel pumps that resulted in engine in-flight shutdowns. We are…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are superseding airworthiness directive (AD) 2007-10-07 for all Turbomeca S.A. Arriel 2B, 2B1, and 2B1A turboshaft engines. AD 2007-10-07 required an inspection of the splines of the coupling assembly and the hydro-mechanical metering unit (HMU) drive gear shaft for wear. This AD requires the same inspection and expands the affected population. This AD also removes Arriel 2B1A engines from the applicability. We a…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are superseding airworthiness directive (AD) 2007-19-09R1 for all Turbomeca S.A. Arriel 2B1 turboshaft engines that do not have modification TU157 incorporated. AD 2007-19-09R1 required replacement of the hydromechanical metering unit (HMU) with a serviceable HMU. This AD requires HMU replacement; reduction of the compliance interval; and inclusion of the power turbine C2 cycle consumption rate when determining c…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for all Turbomeca S.A. Arrius 2B1, 2B1A, 2B2, and 2K1 turboshaft engines. This AD requires initial and repetitive inspections of the hydro-mechanical metering unit (HMU) high pressure pump drive gear shaft splines, cleaning and inspections of the sleeve assembly splines, and replacement of the HMU if it fails inspection. This AD was prompted by in-flight shutdowns c…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for all Turbomeca S.A. ASTAZOU XIV B and XIV H engines. This AD was prompted by reports of cracks on the 2nd-stage turbine disk. This AD requires replacement of the 2nd-stage turbine disk. We are issuing this AD to prevent disk cracking, uncontained 2nd-stage turbine blade release, damage to the engine, and damage to the helicopter.
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for all Turbomeca S.A. Arrius 2F turboshaft engines. This AD requires a one- time inspection of the ejector assembly nozzle of an affected lubricating device and, if a discrepancy is found, removal and replacement with a part eligible for installation. This AD was prompted by an in-flight shutdown (IFSD) of an Arriel 1 engine. We are issuing this AD to prevent failu…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for certain Turbomeca S.A. Arriel 1A1, 1A2, 1B, 1C, 1C1, 1C2, 1D, 1D1, 1E2, 1K1, 1S, and 1S1 turboshaft engines. This AD requires a one-time inspection of the free turbine (FT) module (M04) for the affected Turbomeca S.A. Arriel 1 engines and, if a discrepancy is found, repair of the affected module. This AD was prompted by a "chip illumination event" in flight on a…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are superseding airworthiness directive (AD) 2013-01-07 for all Turbomeca S.A. Arriel 2D turboshaft engines. AD 2013-01-07 required replacing the hydromechanical metering unit (HMU) at a reduced life. This AD maintains that requirement and also requires conducting inspections of the HMU. This AD was prompted by further cases of deterioration of HMU rotating components. We are issuing this AD to prevent an uncomma…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are superseding an existing airworthiness directive (AD) for Turbomeca S.A. Arrius 2B, 2B1, and 2F turboshaft engines. That AD currently requires replacement of injector manifolds and borescope- inspection of the flame tube and the high-pressure (HP) turbine area for possible damage. This new AD requires, depending on the engine model, repetitive replacements of fuel injection manifolds and the privilege injector…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are superseding an existing airworthiness directive (AD) for all Turbomeca S.A. Makila 1A2 turboshaft engines. That AD currently requires replacement of certain serial number (S/N) N2 sensor harnesses. This AD requires replacement of the same S/N harnesses, and requires replacement of additional S/N N2 sensor harnesses. This AD was prompted by corrosion detected in affected N2 sensor harnesses. We are issuing thi…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for Turbomeca S.A. Arriel 2D turboshaft engines. This AD was prompted by a low fuel pressure event caused by deterioration and a loss of the low- pressure drive function within the hydro-mechanical metering unit (HMU). This AD requires replacing the HMU at a reduced life. We are issuing this AD to prevent an uncommanded in-flight shutdown of the engine, and possible…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for all Turbomeca S.A. Arriel 1A1, 1A2, 1B, 1C, 1C1, 1C2, 1D, 1D1, 1E2, 1K1, 1S, and 1S1 turboshaft engines. This AD requires performing a high gas generator speed (NG) rating vibration check. This AD was prompted by several reports of uncommanded in-flight shutdown on Arriel 1 engines. We are issuing this AD to prevent an uncommanded in- flight shutdown of the engi…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are superseding an existing airworthiness directive (AD) for all Turbomeca S.A. Arriel 1A, 1A1, 1A2, 1B, 1C, 1C1, 1C2, 1D, 1D1, 1E, 1E2, 1K, 1K1, 1S, and 1S1 turboshaft engines. That AD currently requires initial and repetitive visual inspections for erosion caused by dust ingestion and, if necessary, cleaning of the gas generator (module M03). This new AD requires determining the engine history; performing a one…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are superseding an existing airworthiness directive (AD) for all Turbomeca S.A. Arriel 1E2, 1S, and 1S1 turboshaft engines. That AD currently requires a one-time inspection and torque check of the 3- way union plug installed on all fuel control units (FCUs). This new AD requires the same actions. This AD also requires reduction of the applicability to certain FCUs and references an updated service bulletin contai…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are superseding an existing airworthiness directive (AD) for certain Turbomeca S.A. Arriel 2B and 2B1 turboshaft engines. That AD currently requires accomplishment of the TU166 modification. This new AD requires adding the Arriel 2S2 and 2C2 engines to the applicability of engines requiring the TU166 modification with different compliance times. This AD was prompted by reports of an accident involving a twin-engi…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for Turbomeca S.A. Arriel 2C1, 2C2, and 2S2 turboshaft engines. This AD requires replacement of affected digital engine control units (DECUs). This AD was prompted by a report of a helicopter experiencing a DECU malfunction during flight. We are issuing this AD to prevent loss of automatic control on one or both engines installed on the same helicopter, which could…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for all Turbomeca S.A. Arriel 2B and 2B1 turboshaft engines. This AD was prompted by the discovery of non-conformities of certain power turbine (PT) blade fir-tree roots. This AD requires removing the affected PT blades from service on or before reaching a new reduced life limit for those certain PT blades. We are issuing this AD to prevent PT blade rupture, which c…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are superseding an existing airworthiness directive (AD) for Turbomeca S.A. Arrius 2F turboshaft engines with P3 air pipe (first section) part number (P/N) 0 319 71 918 0, installed. That AD currently requires inspections of the P3 air pipe (first section) and right-hand (RH) rear half-wall for proper clearance and readjustment of the pipe if necessary. This new AD requires the same inspections for installed engi…
Airworthiness Directives; Turbomeca S.A. Turboshaft Engines
We are superseding an existing airworthiness directive (AD) for all Turbomeca S.A. Arriel 2B and 2B1 turboshaft engines. That AD currently requires checking the transmissible torque between the low- pressure (LP) pump impeller and the high-pressure (HP) pump shaft on high-pressure/low-pressure (HP/LP) pump hydro-mechanical metering units (HMUs) that do not incorporate Modification TU 147. This new AD requires inspec…