Bell helicopter textron canada limited airworthiness directives
100 ADs showing 100 of 119 in the reference matching Bell helicopter textron canada limited — from the Federal Register, checked every weekday. Applicability may depend on serial and effectivity: verify against the official AD before any maintenance action.
Reference last synced: 10/22/2026 16:00 UTC · 10,462 ADs indexed
Airworthiness Directives; Bell Textron Canada Limited Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Bell Textron Canada Limited Model 505 helicopters. This AD was prompted by reports that the identification plate affixed to certain tail cone assemblies contains an incorrect part number (P/N), which may not accurately convey the life limit. This AD requires verifying the tail cone assembly part number and, if necessary, replacing the incorrect tail…
Airworthiness Directives; Bell Textron Canada Limited Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Bell Textron Canada Limited Model 222 helicopters. The FAA previously sent this AD as an emergency AD to all known U.S. owners and operators of these helicopters. This AD was prompted by a report of in- flight fatigue failure of a tail rotor pitch horn. This AD requires removing the affected tail rotor pitch horn and associated tail rotor pitch links…
Airworthiness Directives; Bell Textron Canada Limited (Type Certificate Previously Held by Bell Helicopter Textron Canada Limited) Helicopters
The FAA is superseding Airworthiness Directive (AD) 99-23-18, AD 2005-03-07, AD 2013-12-07, and AD 2014-04-07, which applied to certain Bell Helicopter Textron Canada (now Bell Textron Canada Limited) Model 407 helicopters. AD 99-23-18 required revising the life limits for certain parts, replacing each part that had exceeded its life limit, and revising the Airworthiness Limitation Section (ALS) of the existing main…
Airworthiness Directives; Bell Textron Canada Limited (Type Certificate Previously Held by Bell Helicopter Textron Canada Limited) Helicopters
The FAA is adopting a new airworthiness directive (AD) for Bell Textron Canada Limited (type certificate previously held by Bell Helicopter Textron Canada Limited) Model 206L, 206L-1, 206L-3, and 206L-4 helicopters with a certain part-numbered main rotor (M/R) blade installed under Supplemental Type Certificate (STC) SR02684LA. This AD was prompted by delamination of M/R blades. This AD requires a repetitive inspect…
Airworthiness Directives; Bell Textron Canada Limited (Type Certificate Previously Held by Bell Helicopter Textron Canada Limited) Helicopters
The FAA is superseding Airworthiness Directive (AD) 2019-11-05 for certain Bell Helicopter Textron Canada Limited (now Bell Textron Canada Limited) Model 429 helicopters. AD 2019-11-05 required inspecting the tail rotor (TR) pitch link assemblies, and replacing certain pitch link bearings. This AD was prompted by a report of a worn pitch link, and the FAA's determination that all TR pitch link assemblies are affecte…
Airworthiness Directives; Bell Textron Canada Limited (Type Certificate Previously Held by Bell Helicopter Textron Canada Limited) Helicopters
The FAA is superseding Airworthiness Directive (AD) 2020-20- 06, which applied to certain Bell Helicopter Textron Canada Limited (now Bell Textron Canada Limited) Model 429 helicopters. AD 2020-20-06 required repetitive inspections of certain cyclic and collective assembly bearings. This AD was prompted by new bellcrank assemblies, which have been upgraded with corrosion resistant steel bearings. This AD retains cer…
Airworthiness Directives; Bell Textron Canada Limited (Type Certificate Previously Held by Bell Helicopter Textron Canada Limited) Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Bell Textron Canada Limited (type certificate previously held by Bell Helicopter Textron Canada Limited) Model 505 helicopters. This AD was prompted by the determination that reducing the pressure altitude limitations for certain fuel types is necessary. This AD requires revising the existing Rotorcraft Flight Manual (RFM) for your helicopter. The FA…
Airworthiness Directives; Bell Textron Canada Limited (Type Certificate Previously Held by Bell Helicopter Textron Canada Limited) Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Bell Textron Canada Limited (type certificate previously held by Bell Helicopter Textron Canada Limited) Model 429 helicopters. This AD was prompted by reports of incorrectly staked spherical bearings in the directional control bellcrank assembly. This AD requires a one-time inspection of the lower surface of the spherical bearing in the directional…
Airworthiness Directives; Bell Textron Canada Limited (Type Certificate Previously Held by Bell Helicopter Textron Canada Limited) Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Bell Textron Canada Limited (Bell) Model 429 helicopters. This AD was prompted by reports of tail rotor gearbox assemblies found loose on the gearbox support. This AD requires repetitive torque checks of the tail rotor gearbox attachment hardware, and corrective action if necessary. The FAA is issuing this AD to address the unsafe condition on these…
Airworthiness Directives; Bell Textron Canada Limited (Type Certificate Previously Held by Bell Helicopter Textron Canada Limited)
The FAA is adopting a new airworthiness directive (AD) for certain Bell Helicopter Textron Canada Limited (now Bell Textron Canada Limited) Model 206A, 206B, 206L, 206L-1, 206L-3, and 206L-4 helicopters. This AD was prompted by a report that a certain tail rotor disc assembly, sold as an alternate part, does not conform to the approved configuration. This AD requires determining if an affected part is installed (by…
Airworthiness Directives; Bell Textron Canada Limited (Type Certificate Previously Held by Bell Helicopter Textron Canada Limited) Helicopters
The FAA is adopting a new airworthiness directive (AD) for Bell Textron Canada Limited (type certificate previously held by Bell Helicopter Textron Canada Limited) (Bell) Model 429 helicopters. This AD was prompted by the identification of certain parts needing life limits and certification maintenance requirement (CMR) tasks. This AD requires establishing life limits and CMR tasks for various parts. Depending on th…
Airworthiness Directives; Bell Textron Canada Limited (Type Certificate Previously Held by Bell Helicopter Textron Canada Limited) Helicopters
The FAA is adopting a new airworthiness directive (AD) for Bell Textron Canada Limited (type certificate previously held by Bell Helicopter Textron Canada Limited) (Bell) Model 505 helicopters. This AD was prompted by the discovery of a gap between the transmission restraint assembly aft attachment hardware lower washer and mating airframe truss assembly (truss assembly) clevis lower lug. This AD requires inspecting…
Airworthiness Directives; Bell Textron Canada Limited (Type Certificate Previously Held by Bell Helicopter Textron Canada Limited) Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Bell Textron Canada Limited (type certificate previously held by Bell Helicopter Textron Canada Limited) Model 206L series helicopters. This AD was prompted by a manufacturing flaw that could cause low fuel level detector switch units (switch units) to hang in the high position and fail to indicate a low fuel condition. This AD requires removing cert…
Airworthiness Directives; Bell Textron Canada Limited (Type Certificate Previously Held by Bell Helicopter Textron Canada Limited) Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Bell Textron Canada Limited (type certificate previously held by Bell Helicopter Textron Canada Limited) Model 429 helicopters. This AD was prompted by the introduction of a new life limit for the centrifugal force bearing (CFB). This AD requires determining the accumulated retirement index number (RIN) and removing each affected CFB from service bef…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Helicopters
The FAA is adopting a new airworthiness directive (AD) for Bell Helicopter Textron Canada Limited (BHTC) Model 429 helicopters. This AD requires repetitive inspections of certain cyclic and collective assembly bearings. This AD was prompted by reports that precipitation can lead to reduced effectiveness of the grease in the bearings. The actions of this AD are intended to address an unsafe condition on these product…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Bell Helicopter Textron Canada Limited (Bell) Model 505 helicopters. This AD requires inspecting each swashplate assembly bearing (bearing), and depending on the inspection results, removing the bearing from service. This AD was prompted by a report of a bearing that migrated out of the swashplate inner ring. The actions of this AD are intended to ad…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Helicopters
The FAA is superseding Airworthiness Directive (AD) 2016-02-06 for Bell Helicopter Textron Canada Limited (Bell) Model 429 helicopters. AD 2016-02-06 required inspecting certain tail rotor (T/R) pitch link bearing bores for corrosion and pitting. AD 2016-02-06 also required a repetitive inspection of the sealant and repeating the inspections for corrosion and pitting if any sealant is missing. This new AD retains th…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Bell Helicopter Textron Canada Limited (Bell Canada) Model 429 helicopters. This AD requires inspecting a certain part-numbered curvic coupling for proper engagement and depending on the inspection results, inspecting for play, inspecting the curvic coupling teeth, inspecting the flapping bearing teeth, replacing parts, performing a rigging check, an…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Helicopters
The FAA is adopting a new airworthiness directive (AD) for Bell Helicopter Textron Canada Limited (BHTC) Model 427 helicopters. This AD requires inspecting the inboard skin of the vertical fin around the four tailboom attachment points. This AD was prompted by reports of cracked vertical fin skins that resulted from metal fatigue. The actions of this AD are intended to prevent an unsafe condition on these products.
Airworthiness Directives; Bell Helicopter Textron Canada Limited Helicopters
We are superseding Airworthiness Directive (AD) 2015-22-02 for certain Bell Helicopter Textron Canada Limited (Bell) Model 429 helicopters. AD 2015-22-02 required inspecting the tail rotor (TR) pitch link assemblies. This AD retains the inspections of AD 2015-22-02 and requires replacing certain pitch link bearings. This AD was prompted by a new design bearing introduced by Bell. We are issuing this AD to address th…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Helicopters
We are adopting a new airworthiness directive (AD) for Bell Helicopter Textron Canada Limited (Bell) Model 206A, 206B, 206L, 206L- 1, 206L-3, 206L-4, and 407 helicopters. This AD requires inspecting and cleaning the oil supply restrictor (restrictor) to the freewheel assembly. This AD was prompted by reports of a blocked oil line restrictor in the freewheel lubrication system. The actions of this AD are intended to…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Helicopters
We are adopting a new airworthiness directive (AD) for Bell Helicopter Textron Canada Limited (BHTC) Model 429 helicopters. This AD requires inspecting each main rotor pitch link rod end bearing assembly (bearing) for wear and play. This AD was prompted by reports of worn bearings. The actions of this AD are intended to prevent an unsafe condition on these products.
Airworthiness Directives; Bell Helicopter Textron Canada Limited Helicopters
We are adopting a new airworthiness directive (AD) for Bell Helicopter Textron Canada Limited (Bell) Model 429 helicopters. This AD revises the life limit for the nose landing gear (NLG) assembly. This AD was prompted by revised airworthiness limitations determined by Bell. The actions of this AD are intended to prevent an unsafe condition on these products.
Airworthiness Directives; Bell Helicopter Textron Canada Limited Helicopters
We are superseding Airworthiness Directive (AD) 2017-13-03 for Bell Helicopter Textron Canada Limited (Bell) Model 429 helicopters. AD 2017-13-03 required adding an identification number to life-limited rod ends that do not have a serial number (S/N). Since we issued AD 2017- 13-03, an additional life-limited rod end was identified that is affected by the same unsafe condition. This new AD retains the requirements o…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Helicopters
We are publishing a new airworthiness directive (AD) for Bell Helicopter Textron Canada Limited (Bell) Model 429 helicopters. This AD was sent previously to all known U.S. owners and operators of these helicopters as Emergency AD 2018-16-51, dated July 26, 2018, which superseded Emergency AD 2018-15-51, dated July 20, 2018. This AD requires inspecting the tail rotor (T/R) gearbox installation, inspecting the T/R gea…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Helicopters
We are adopting a new airworthiness directive (AD) for certain serial numbered Bell Helicopter Textron Canada Limited (BHTC) Model 429 helicopters. This AD requires marking a serial number on life-limited forward spars and actuator fitting assemblies. The actions of this AD are intended to prevent an unsafe condition on these products.
Airworthiness Directives; Bell Helicopter Textron Canada Limited (Bell) Helicopters
We are adopting a new airworthiness directive (AD) for Bell Model 407 helicopters. This AD requires repetitive inspections of the tail rotor (TR) driveshaft segment assemblies and a torque check of the TR adapter retention nuts. This AD was prompted by a report of an in- flight failure of the TR drive system. The actions of this AD are intended to detect and correct an unsafe condition on these products.
Airworthiness Directives; Bell Helicopter Textron Canada Limited
We are adopting a new airworthiness directive (AD) for Bell Helicopter Textron Canada Limited (Bell) Model 429 helicopters. This AD requires reducing the life limit of certain landing gear parts and is prompted by a stress analysis. The actions of this AD are intended to address an unsafe condition on these products.
Airworthiness Directives; Bell Helicopter Textron Canada Limited Helicopters
We are adopting a new airworthiness directive (AD) for Bell Helicopter Textron Canada Limited (Bell) Model 429 helicopters. This AD requires adding an identification number to life-limited rod ends that do not have a serial number (S/N). The actions of this AD are intended to address an unsafe condition on these products.
Airworthiness Directives; Bell Helicopter Textron Canada Helicopters
We are publishing a new airworthiness directive (AD) for Bell Helicopter Textron Canada (Bell) Model 429 helicopters. This AD requires inspecting the condenser blower motor (motor) and condenser blower (blower) to determine if the motor is securely attached to the blower support (shroud). This AD is prompted by a report that the motor detached from the blower. The actions of this AD are intended to prevent an unsafe…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Helicopters
We are adopting a new airworthiness directive (AD) for certain Bell Helicopter Textron Canada Limited (BHTC) Model 206 helicopters. This AD requires removing certain tension-torsion straps (TT straps) from service and is prompted by reports of corroded TT straps. These actions are intended to prevent an unsafe condition on these products.
Airworthiness Directives; Bell Helicopter Textron Canada Limited (Bell) Helicopters
We are adopting a new airworthiness directive (AD) for Bell Model 427 and Model 429 helicopters. This AD requires replacing certain engine and transmission oil check valves. This AD also prohibits installing the affected check valves on any helicopter. This AD is prompted by a report of several cracked or leaking check valves. These actions are intended to detect and prevent a cracked or leaking check valve which co…
Airworthiness Directives; Bell Helicopter Textron Canada Helicopters
We are superseding Airworthiness Directive (AD) 2010-19-51 for Bell Helicopter Textron Canada (Bell) Model 222, 222B, 222U, 230, and 430 helicopters. AD 2010-19-51 required inspecting parts of the main rotor hydraulic servo actuator (servo actuator) for certain conditions and replacing any unairworthy parts before further flight. This new AD requires installing a servo actuator with a new stainless steel piston rod.…
Airworthiness Directives; Bell Helicopter Textron Canada Limited
We are adopting a new airworthiness directive (AD) for Bell Helicopter Textron Canada Limited (Bell) Model 429 helicopters. This AD requires inspecting each tail rotor (T/R) pitch link (link) bearing bore for corrosion and pitting and either replacing the T/R link or applying sealant. This AD also requires a recurring inspection of the sealant and repeating the inspections for corrosion and pitting if any sealant is…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Helicopters
We are superseding emergency airworthiness directive (AD) No. 2015-16-51 (Emergency AD 2015-16-51) for Bell Helicopter Textron Canada Limited (Bell) Model 429 helicopters. Emergency AD 2015-16-51 required inspections of each inboard and outboard tail rotor pitch link assembly for axial or radial bearing play, and if there was axial or radial bearing play, removing the tail rotor pitch link and inspecting for wear. E…
Airworthiness Directives; Bell Helicopter Textron Canada (Bell) Helicopters
We are superseding Airworthiness Directive (AD) 2001-13-51 for Bell Model 206L-4, 407, and 427 helicopters. AD 2001-13-51 required inspecting certain driveshafts for a crack, a loose bolt or nut, or red powder residue and replacing a driveshaft if there is a crack, a loose bolt or nut, or red powder residue. AD 2001-13-51 also required notifying the FAA within 10 days if a crack is found in the driveshaft. This new…
Airworthiness Directives; Bell Helicopter Textron Canada Limited
We are adopting a new airworthiness directive (AD) for certain Bell Helicopter Textron Canada Limited (Bell) Model 206L-1, 206L-3, and 206L-4 helicopters. This AD requires installing a placard and revising the limitations section of the rotorcraft flight manual (RFM). This AD was prompted by several incidents of third stage engine turbine wheel failures caused by excessive vibrations at certain engine speeds during…
Airworthiness Directives; Bell Helicopter Textron Canada Helicopters
We are adopting a new airworthiness directive (AD) for Bell Helicopter Textron Canada (BHTC) Model 407 helicopters. This AD requires inspecting the aft fuselage upper skin (upper skin) for a crack and the upper left longeron assembly (longeron assembly) for a crack, corrosion, or defect. This AD requires replacing or repairing a part or section, depending on the inspection's outcome. This AD was prompted by reports…
Airworthiness Directives; Bell Helicopter Textron Canada (Bell) Helicopters
We are superseding Airworthiness Directive (AD) 2003-05-03 for Bell Model 407 helicopters. AD 2003-05-03 required preflight checking and repetitively inspecting for a crack in certain tailbooms that have been redesigned, replacing the tailboom if there is a crack, modifying and re-identifying certain tailbooms, installing an improved horizontal stabilizer assembly, and assigning a 5,000 hour time-in-service (TIS) li…
Airworthiness Directives; Bell Helicopter Textron Canada Limited (Bell) Helicopters
We are adopting a new airworthiness directive (AD) for Bell Model 206L, L-1, L-3, and L-4 helicopters. This AD requires measuring each main rotor (M/R) blade spar space to determine whether it is oversized and reidentifying the M/R blade and reducing the life limit of the blade if the spar spacer is oversized. This AD was prompted by the manufacture of certain blades with an oversized spar spacer and the determinati…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Helicopters
We are adopting a new airworthiness directive (AD) for certain serial-numbered Bell Helicopter Textron Canada Limited (BHTC) Model 206L, 206L-1, 206L-3, and 206L-4 helicopters with a certain tailboom upper left attachment fitting (fitting). This AD requires inspecting the fitting for a crack and other conditions. This AD was prompted by the manufacturer revising and extending the 100 hour time-in-service (TIS) inspe…
Airworthiness Directives; Bell Helicopter Textron Canada Limited (Bell) Helicopters
We are adopting a new airworthiness directive (AD) for certain Bell Model 206B and 206L helicopters. This AD requires installing a placard beneath the engine power dual tachometer and revising the operating limitations section of the rotorcraft flight manual (RFM). This AD was prompted by several incidents of third stage engine turbine wheel failures, which were caused by excessive vibrations at certain engine speed…
Airworthiness Directives; Bell Helicopter Textron Canada (Bell) Helicopters
We are adopting a new airworthiness directive (AD) for Bell Model 206L-4 and 407 helicopters. This AD requires replacing or reworking certain aft bearing caps. This AD was prompted by the manufacture of certain freewheel aft bearing caps without a lubrication channel to allow oil flow into the aft bearing support assembly. The actions of this AD are intended to prevent failure of the freewheel unit and subsequent lo…
Airworthiness Directives; Bell Helicopter Textron Canada Limited (Bell) Helicopters
We are adopting a new airworthiness directive (AD) for certain Bell Model 407 helicopters. This AD requires installing a placard beneath the NR/NP dual tachometer and revising the limitations section of the rotorcraft flight manual (RFM). This AD was prompted by several incidents of third stage engine turbine wheel failures, which were caused by excessive vibrations at certain engine speeds during steady- state oper…
Airworthiness Directives; Bell Helicopter Textron Canada Limited (Bell) Helicopters
We are adopting a new airworthiness directive (AD) for Bell Model 230 helicopters. This AD requires installing a placard on the instrument panel and revising the limitations section of the rotorcraft flight manual (RFM). This AD was prompted by several incidents of third stage engine turbine wheel failures, which were caused by excessive vibrations at certain engine speeds during steady-state operations. These actio…
Airworthiness Directives; Bell Helicopter Textron Canada Limited (Bell) Helicopters
We are adopting a new airworthiness directive (AD) for Bell Model 206A, 206B, 206L, 206L-1, 206L-3, 206L-4, 222, 222B, 222U, 230, 407, 427, and 430 helicopters. This AD requires inspecting each bearing to determine if it has been properly staked and replacing the bearing or assembly if it has not been properly staked. This AD was prompted by bearings not being properly staked and migrating out of their proper positi…
Airworthiness Directives; Bell Helicopter Textron Canada Inc. Helicopters
We are adopting a new airworthiness directive (AD) for certain Bell Helicopter Textron Canada Inc. (BHT) Model 206A, 206B, and 206L helicopters. This AD requires replacing certain part-numbered engine auto-relight kit control boxes. This AD was prompted by a design review that revealed the control box chipset did not meet the required temperature range requirements, which could cause the control box to malfunction,…
Airworthiness Directives; Bell Helicopter Textron Canada Helicopters
We are adopting a new airworthiness directive (AD) for Bell Helicopter Textron Canada (BHTC) Model 407 helicopters with certain tailboom assemblies installed. This AD requires, at specified intervals, inspecting the tailboom assembly for a crack, loose rivet, or other damage. This AD was prompted by a stress analysis of the tailboom skin that revealed that high-stress-concentration areas are susceptible to skin crac…
Airworthiness Directives; Bell Helicopter Textron Canada (Bell) Helicopters
We are adopting a new airworthiness directive (AD) for Bell Model 430 helicopters, which requires replacing certain components of the air data system. This AD was prompted by the discovery of incorrect indicated airspeed when the helicopter was tested to the cold temperature limits (-40 degrees centigrade) required for Category A operations. The actions of this AD are intended to correct the published Vne and to cor…
Airworthiness Directives; Bell Helicopter Textron Canada Limited (Bell) Helicopters
We are adopting a new airworthiness directive (AD) for Bell Model 206L, 206L-1, 206L-3, and 206L-4 helicopters. This AD requires inspecting certain hydraulic servo actuator assemblies (servo) for a loose nut, shaft, and clevis assembly, modifying or replacing the servo as necessary, and reidentifying the servo. This AD is prompted by an investigation after an accident and the determination that there was a loose con…
Airworthiness Directives; Bell Helicopter Textron Canada Helicopters
We are adopting a new airworthiness directive (AD) for the Bell Helicopter Textron Canada Limited (BHTC) Model 407 helicopters. This AD requires you to replace tailboom-attachment hardware (attachment hardware), and perform initial and recurring determinations of the torque on the nuts of the tailboom-attachment bolts (bolts) at all four attachment locations. This AD was prompted by a review of the tailboom-attachme…
Airworthiness Directives; Bell Helicopter Textron Canada Helicopters
We are adopting an airworthiness directive (AD) superseding an existing airworthiness directive for Bell Helicopter Textron Canada (Bell) Model 407 and 427 helicopters. The existing AD requires inspecting certain hydraulic servo actuators (servo) to determine whether the shaft turns independently of the nut or the clevis assembly, and additional actions based upon the inspection's outcome. The AD also requires reide…
Airworthiness Directives; Bell Helicopter Textron Canada, Limited, Helicopters
We are adopting a new airworthiness directive (AD) for Bell Helicopter Textron Canada (Bell) Model 206, 206A, 206A-1, 206B, 206B-1, 206L, 206L-1, 206L-3, and 206L-4 helicopters, with Aviation Specialties Unlimited, Inc. (ASU), Night Vision Imaging System (NVIS) lighting modified by Supplemental Type Certificate SR01383SE (STC). This AD requires determining the date of STC installation, determining if the aircraft ha…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Helicopters
We are adopting a new airworthiness directive (AD) for Bell Helicopter Textron Canada Limited (BHTC) Model 427 helicopters which requires replacing certain tailboom attachment hardware and at certain intervals thereafter, determining the torque of that tailboom attachment hardware. This AD was prompted by a review of the tailboom attachment installation, which revealed that the torque value of the bolts specified in…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Helicopters
We are publishing a new airworthiness directive (AD) for Bell Helicopter Textron Canada Limited (Bell) Model 206L, 206L-1, 206L-3, and 206L-4 helicopters with certain main rotor blades installed to reduce the life limit of those blades. This AD is prompted by two accidents and the subsequent investigations that revealed that, in each accident, a main rotor blade failed because of fatigue cracking. These actions are…
Airworthiness Directives; Bell Helicopter Textron Canada (Bell) Model 407 and 427 Helicopters
This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 2011-15-51, which was sent previously to all known U.S. owners and operators of the specified Bell Model 407 and 427 helicopters by individual letters. This AD requires inspecting certain hydraulic servo actuators to determine whether the shaft turns independently of the nut or the clevis assembly. If the shaft turns i…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Model 427 Helicopters
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Bell Helicopter Textron Canada Limited (BHTC) Model 206A, 206B, 206L, 206L-1, 206L-3, 206L-4, 222, 222B, 222U, 230, 407, 427, and 430 Helicopters
This document publishes in the Federal Register an amendment adopting Emergency Airworthiness Directive (AD) 2010-26-51, which was sent previously to all known U.S. owners and operators of the specified model helicopters by individual letters. This AD also supersedes existing AD 2009-08-03. This AD is prompted by another incident in which the tail rotor blade (blade) tip weight separated from a blade during flight c…
Airworthiness Directives; Bell Helicopter Textron Canada Model 222, 222B, 222U, 230, and 430 Helicopters
This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 2010-19-51, which was sent previously to all known U.S. owners and operators of the specified model Bell Helicopter Textron Canada (Bell) helicopters by individual letters. This AD requires inspecting parts of the main rotor hydraulic servo actuator (servo actuator) for certain conditions and replacing any unairworthy…
Airworthiness Directives; Bell Helicopter Textron Canada Model 222, 222B, 222U, 230, and 430 Helicopters
This amendment supersedes an existing airworthiness directive (AD) for the specified Bell Helicopter Textron Canada (BHTC) helicopters, that currently requires certain checks and inspections of the tail rotor blades. If a crack is found, the existing AD requires replacing the tail rotor blade (blade) with an airworthy blade before further flight. This amendment requires the same checks and inspections of the blades…
Airworthiness Directives; Bell Helicopter Textron Canada (BHTC) Model 407 and Model 427 Helicopters
We are adopting a new airworthiness directive (AD) for the BHTC Model 407 and Model 427 helicopters. This AD results from mandatory continuing airworthiness information (MCAI) ADs issued by the aviation authority of Canada. The MCAI ADs state that some hydraulic pump driveshaft assemblies may have been delivered with a missing internal plug or fastening rivet. This condition, if not corrected, could result in a loss…
Airworthiness Directives; Bell Helicopter Textron Canada Model 407 and 427 Helicopters
We are adopting a new airworthiness directive (AD) for Bell Helicopter Textron Canada (Bell) Model 407 and 427 helicopters. This AD results from a mandatory continuing airworthiness information (MCAI) AD issued by the aviation authority of Canada. The MCAI AD states that, during a preflight check, it was observed that the swashplate link assembly bearing had moved in the lever race, making contact with the swashplat…
Airworthiness Directives; Bell Helicopter Textron Canada Model 427 Helicopters
We are adopting a new airworthiness directive (AD) for Bell Helicopter Textron Canada (BHTC) Model 427 helicopters. This AD results from mandatory continuing airworthiness information (MCAI) originated by the aviation authority of Canada to identify and correct an unsafe condition on an aviation product. Transport Canada, the aviation authority of Canada, with which we have a bilateral agreement, states that it has…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Model 206A Series, 206B Series, 206L Series, 407, and 427 Helicopters
This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 2009-07-52 and supersedes Emergency AD 2009-07-51, issued March 17, 2009, which was sent previously to all known U.S. owners and operators of Bell Helicopter Textron Canada Limited (Bell) Model 206A series, 206B series, 206L series, 407, and 427 helicopters by individual letters. This AD requires, before further flight…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Model 206A, 206B, 206L, 206L-1, 206L-3, 206L-4, 222, 222B, 222U, 230, 407, 427, and 430 Helicopters
We are adopting a superseding airworthiness directive (AD) for the specified Bell Helicopter Textron Canada Limited (BHTC) Model 206A, 206B, 206L, 206L-1, 206L-3, 206L-4, 222, 222B, 222U, 230, 407, 427, and 430 helicopters. That AD currently requires replacing each affected tail rotor blade (blade) with an airworthy blade that has a serial number not listed in the Rotor Blades, Inc. (RBI) document that is attached t…
Airworthiness Directives; Bell Helicopter Textron Canada Model 222, 222B, 222U, 230, and 430 Helicopters
We are superseding an existing airworthiness directive (AD) for Bell Helicopter Textron Canada (Bell) Model 222, 222B, 222U, 230, and 430 helicopters. That AD currently requires visually inspecting the main rotor hydraulic actuator support (support) to verify the presence of all dowel pins and sealant between the support and transmission and verifying the proper torque of each attaching nut (nut). This AD requires t…
Airworthiness Directives; Bell Helicopter Textron Canada (BHTC) Model 230 Helicopters
We are adopting a new airworthiness directive (AD) for BHTC Model 230 helicopters. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of Canada which indicates that the existing rigging procedures for the tail rotor pitch change mechanism have to be changed due to the possibility of parts interference. The cumulative effect of individual part tolerances result…
Airworthiness Directives; Bell Helicopter Textron Canada (BHTC) Model 222, 222B, and 222U Helicopters
We are adopting a new airworthiness directive (AD) for BHTC Model 222, 222B, and 222U helicopters. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The aviation authority of Canada, with which we have a bilateral agreement, states in the MCAI: "It has been determined that t…
Airworthiness Directives; Bell Helicopter Textron Canada (BHTC) Model 430 Helicopters
We are adopting a new airworthiness directive (AD) for BHTC Model 430 helicopters. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The aviation authority of Canada, with which we have a bilateral agreement, states in the MCAI: "It has been determined that the existing…
Airworthiness Directives; Bell Helicopter Textron Canada Model 206L, L-1, L-3, L-4, and 407 Helicopters
We are adopting a new airworthiness directive (AD) for the specified Bell Helicopter Textron Canada (BHTC) helicopters. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority to identify and correct an unsafe condition on an aviation product. The Aviation Authority of Canada with whom we have a bilateral agreement states in the MCAI: "Horizontal stabilizers par…
Airworthiness Directives; Bell Helicopter Textron Canada Model 206A, 206B, 206L, 206L-1, 206L-3, and 206L-4 Helicopters
We are adopting a new airworthiness directive (AD) for the specified Bell Helicopter Textron Canada (BHTC) Model 206A, 206B, 206L, 206L-1, 206L-3, and 206L-4 helicopters. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority to identify and correct an unsafe condition on an aviation product. The aviation authority of Canada, with which we have a bilateral agre…
Airworthiness Directives; Bell Helicopter Textron Canada Model 222, 222B, 222U, 230 and 430 Helicopters
This amendment adopts a new airworthiness directive (AD) for Bell Helicopter Textron Canada (BHTC) Model 222, 222B, 222U, 230 and 430 helicopters that requires rewiring and testing the fuel valve switch on each engine and testing the ignitor system. This amendment is prompted by an in-flight incident in which a fuel valve switch failed, causing the fuel valve to inadvertently close. The actions specified by this AD…
Airworthiness Directives; Bell Helicopter Textron Canada Model 430 Helicopters
This amendment adopts a new airworthiness directive (AD) for Bell Helicopter Textron Canada (BHTC) Model 430 helicopters that requires replacing a certain servo actuator-to-actuator support attachment bolt (bolt) with an airworthy bolt. This action also requires establishing a retirement life for certain bolts and recording the retirement life on a component history card or equivalent record. This amendment is promp…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Model 206A and 206B Helicopters
This amendment adopts a new airworthiness directive (AD) for Bell Helicopter Textron Canada Limited (BHTC) Model 206A and 206B helicopters, serial numbers (S/N) 0004 through 3906, with two-piece vertical stabilizer (fin) supports (fin supports) installed, that requires inserting a revision into the applicable maintenance manual, verifying the torque on the fin support attachment hardware, inspecting the fin support…
Airworthiness Directives; Bell Helicopter Textron Canada Model 206A and 206B Helicopters
We are adopting a new airworthiness directive (AD) for Bell Helicopter Textron Canada (BHTC) Model 206A and 206B helicopters. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority to identify and correct an unsafe condition on an aviation product. The aviation authority of Canada, with which we have a bilateral agreement, states in the MCAI:
Airworthiness Directives; Bell Helicopter Textron Canada Limited Model 206A, 206B, 206L, 206L-1, 206L-3, 206L-4, 222, 222B, 222U, 230, 407, 427, and 430 Helicopters
This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 2007-19-52, which was sent previously to all known U.S. owners and operators of the specified Bell Helicopter Textron Canada Limited (BHTC) model helicopters by individual letters. This AD requires replacing each affected tail rotor blade (blade) with an airworthy blade with a serial number not listed in the Rotor Blad…
Airworthiness Directives; Bell Helicopter Textron Canada Model 206A and 206B Series Helicopters
We are adopting a new airworthiness directive (AD) for Bell Helicopter Textron Canada (Bell) Model 206A and 206B series helicopters. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority to identify and correct an unsafe condition on an aviation product. The aviation authority of Canada, with which we have a bilateral agreement, states in the MCAI:
Airworthiness Directives; Bell Helicopter Textron Canada Model 206A, B, L, L-1, L-3, and L-4 Helicopters
This amendment supersedes an existing airworthiness directive (AD) for the specified Bell Helicopter Textron Canada (BHTC) model helicopters. The existing AD currently requires certain inspections and checks of the tail rotor blade (blade) for a deformation, a crack, and a bent or deformed tail rotor weight (weight). Also, that AD requires, before further flight, replacing each blade with an airworthy blade if a def…
Airworthiness Directives; Bell Helicopter Textron Canada Model 222, 222B, 222U, 230, and 430 Helicopters
This amendment adopts a new airworthiness directive (AD) for the specified Bell Helicopter Textron Canada (BHTC) model helicopters. This action requires initial and repetitive inspections of each tail rotor counterweight bellcrank (bellcrank) with a specified part number and serial number. If external damage, a crack, roughness, or looseness between the bearing set and bellcrank is found or if bearing set axial play…
Airworthiness Directives; Bell Helicopter Textron Canada Model 206A, A-1, B, B-1, L, L-1, L-3, L-4 Helicopters
This amendment adopts a new airworthiness directive (AD) for the specified Bell Helicopter Textron Canada (BHTC) model helicopters that requires, before the first flight of each day, checking the tail rotor blade (blade) root doublers (doublers) for an edge void or de- bond on both sides of each blade, and if an edge void or de-bond is found, replacing the unairworthy blade with an airworthy blade. This AD also requ…
Airworthiness Directives; Bell Helicopter Textron Canada Model 407 Helicopters
This amendment adopts a new airworthiness directive (AD) for Bell Helicopter Textron Canada (Bell) Model 407 helicopters that requires creating a component history card or equivalent record for each crosstube assembly, converting accumulated run-on landings to an accumulated Retirement Index Number (RIN) count, and establishing a maximum accumulated RIN for certain crosstube assemblies. This amendment is prompted by…
Airworthiness Directives; Bell Helicopter Textron Canada Model 222, 222B, 222U, 230, and 430 Helicopters
This amendment supersedes an existing airworthiness directive (AD) for the specified Bell Helicopter Textron Canada (BHTC) model helicopters that currently requires certain checks and inspections of the tail rotor blades. If a crack is found, the existing AD requires replacing the tail rotor blade (blade) with an airworthy blade before further flight. This amendment requires the same checks and inspections as the ex…
Airworthiness Directives; Bell Helicopter Textron Canada Model 222, 222B, 222U, 230, and 430 Helicopters
This amendment adopts a new airworthiness directive (AD) for the specified Bell Helicopter Textron (BHTC) model helicopters. This action requires certain checks and inspections of the tail rotor blades. If a crack is found, before further flight, this AD requires replacing the tail rotor blade (blade) with an airworthy blade. This amendment is prompted by three reports of cracked blades found during scheduled inspec…
Airworthiness Directives; Bell Helicopter Textron Canada Model 206A, B, L, L-1, L-3, and L-4 Helicopters
This amendment adopts a new airworthiness directive (AD) for the specified Bell Helicopter Textron Canada (BHTC) model helicopters. This action requires an initial inspection and, at specified intervals, certain repetitive checks and inspections of the tail rotor blade (blade) for a deformation, a crack, and a bent or deformed tail rotor weight (weight). Also, this action requires, before further flight, replacing e…
Airworthiness Directives; Bell Helicopter Textron Canada Model 206L-1 and 206L-3 Helicopters
This amendment adopts a new airworthiness directive (AD) for the specified Bell Helicopter Textron Canada (Bell) model helicopters that requires a one-time inspection of the adjustable stop screws of the magnetic brake assembly; repairing, as appropriate, certain mechanical damage to the cyclic and collective flight control magnetic brake arm assembly (arm assembly), if necessary; and installing the stop screw with…
Airworthiness Directives; Bell Helicopter Textron Canada Model 222, 222B, 222U, and 230 Helicopters
This amendment adopts a new airworthiness directive (AD) for the specified Bell Helicopter Textron Canada (BHTC) model helicopters that requires certain inspections of the main rotor yoke (yoke) for a crack, fretting, or buffer deterioration. If a crack is found, the AD requires replacing the yoke with an airworthy yoke before further flight. If fretting or buffer deterioration are found, the AD requires further ins…
Airworthiness Directives; Bell Helicopter Textron Canada Model 407 Helicopters
This amendment supersedes an existing airworthiness directive (AD) for Bell Helicopter Textron Canada (BHTC) Model 407 helicopters which requires a one-time replacement of certain oil cooler blower bearings. Also, the existing AD requires adding a limitation and caution to the rotorcraft flight manual (RFM) and inspecting, replacing, and lubricating certain bearings at specified intervals. This amendment adds certai…
Airworthiness Directives; Bell Helicopter Textron Canada Model 206A, 206A-1, 206B, 206B-1, 206L, 206L-1, 206L-3, and 206L-4 Helicopters
This amendment adopts a new airworthiness directive (AD) for the specified Bell Helicopter Textron Canada (BHTC) model helicopters that requires performing a continuity test, temporarily repairing any unairworthy chip detector, and replacing any repaired chip detectors. This amendment is prompted by reports of poor or no continuity between the insert and the chip detector housing on certain chip detectors. The actio…
Airworthiness Directives; Bell Helicopter Textron Canada Model 222, 222B, and 222U Helicopters
This amendment adopts a new airworthiness directive (AD) for the specified Bell Helicopter Textron Canada (Bell) model helicopters that requires a one-time inspection of the adjustable stop screws of the magnetic brake assembly; repairing, as appropriate, certain mechanical damage to the cyclic and collective flight control magnetic brake arm assembly (arm assembly), if necessary; and installing the stop screw with…
Airworthiness Directives; Bell Helicopter Textron Canada Model 222, 222B, 222U, and 230 Helicopters
This amendment adopts a new airworthiness directive (AD) for Bell Helicopter Textron Canada (BHTC) Model 222, 222B, 222U, and 230 helicopters. This action requires inspecting the main rotor pendulum weight support (pendulum weight support) for file or grinding marks, gouges, and appropriate edge breaks. It also requires, if necessary, reworking and remarking or replacing the pendulum weight support. Regardless, this…
Airworthiness Directives; Bell Helicopter Textron Canada Model 407 Helicopters
This amendment adopts a new airworthiness directive (AD) for the specified Bell Helicopter Textron Canada (Bell) model helicopters that requires preflight checking and repetitively inspecting for a crack in certain tailbooms that have not been redesigned and replacing the tailboom if a crack is found; modifying and re-identifying certain tailbooms and installing an improved horizontal stabilizer assembly; and assign…
Airworthiness Directives; Bell Helicopter Textron Canada (Bell) Model 427 Helicopters
This amendment adopts a new airworthiness directive (AD) for the specified Bell model helicopters that requires replacing the hydraulic solenoid tee fitting (tee fitting) and tubes. This amendment is prompted by the manufacturer's discovery that tee fittings may be installed improperly and restrict hydraulic fluid flow. The actions specified by this AD are intended to prevent restricted flow of hydraulic fluid to th…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Model 427 Helicopters
This amendment adopts a new airworthiness directive (AD) for the specified Bell Helicopter Textron Canada (Bell) model helicopters that requires modifying the auxiliary fin assemblies and revising the Limitations section of the Rotorcraft Flight Manual (RFM) to reduce the never-exceed speed (Vne) for a tail rotor pedal stop failure. This amendment is prompted by several incidents of main rotor blades contacting the…
Airworthiness Directives; Bell Helicopter Textron Canada Model 407 Helicopters
This amendment supersedes an existing emergency airworthiness directive (EAD), which was sent previously to all known U.S. owners and operators of Bell Helicopter Textron Canada (Bell) helicopters by individual letters. That EAD requires a visual check to ensure that the two swashplate drive link cup washers (cup washers) are installed correctly. If a cup washer is installed incorrectly, removing and replacing the s…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Model 407 Helicopters
This amendment adopts a new airworthiness directive (AD) for Bell Helicopter Textron Canada Limited (Bell) Model 407 helicopters. This action requires visually inspecting certain tailboom gearbox support castings (castings) for cracks and replacing the tailboom assembly if a crack is found. This amendment is prompted by an incident in which a crack was discovered on the casting that holds the tail rotor gearbox and…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Model 206L, L-1, L-3, and L-4 Helicopters
This amendment supersedes an existing airworthiness directive (AD) for the specified Bell Helicopter Textron Canada Limited (BHTCL) model helicopters that currently requires removing the horizontal stabilizer supports and inspecting the edges of the tailboom skins around the horizontal stabilizer openings for a crack. This amendment requires checking and inspecting the tailboom for a crack and modifying or replacing…
Airworthiness Directives; Bell Helicopter Textron Canada Limited Model 407 Helicopters
This amendment supersedes an existing airworthiness directive (AD) for Bell Helicopter Textron Canada Limited (BHTCL) Model 407 helicopters that requires visually inspecting the brackets that attach the horizontal stabilizer slat (slat) to the stabilizer for a crack. If a crack is found, that AD also requires replacing the slat assembly before further flight. Also, that AD requires installing airworthy, segmented sl…
Airworthiness Directives; Bell Helicopter Textron Canada Model 222, 222B, 222U, and 230 Helicopters
This document publishes in the Federal Register an amendment adopting Emergency Airworthiness Directive (EAD) 2002-08-54, which was sent previously to all known U.S. owners and operators of the specified Bell Helicopter Textron Canada (BHTC) model helicopters by individual letters. This AD requires a visual check of each main rotor grip assembly (grip) and pitch horn at specified intervals and a visual inspection us…
Airworthiness Directives; Bell Helicopter Textron Canada Model 407 Helicopters
This amendment adopts a new airworthiness directive (AD) for Bell Helicopter Textron Canada (BHTC) Model 407 helicopters that requires visually inspecting the forward hanger bearing bracket (bracket) for a crack. This amendment is prompted by reports of cracks in the bracket. The actions specified by this AD are intended to detect a crack in the bracket, to prevent loss of tail rotor drive or control and subsequent…
Airworthiness Directives; Bell Helicopter Textron Canada Model 407 Helicopters
This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 2002-06-52, which was sent previously to all known U.S. owners and operators of Bell Helicopter Textron Canada (BHTC) Model 407 helicopters by individual letters. This AD requires a one-time replacement of certain bearings and, before further flight, adding a limitation and caution to the rotorcraft flight manual (RFM)…